Atomizer Short Error on a Geekvape: What Does It Mean?
Are you seeing an “Atomizer Short” error message on the screen when you try to use your Geekvape? This is a fairly common error with vape mods and indicates that the device either can’t detect the resistance of the installed pod or coil or that the detected resistance isn’t within the device’s supported range.
An Atomizer Short error can potentially stem from a permanent problem with the device or the coil, but it’s more often completely fixable. Reading this guide, you’ll learn how to get to the root of the problem.
Check for a Leak Under the Tank or Pod
The first thing that you should always do if your Geekvape displays an Atomizer Short error is look under the tank or pod to see if e-liquid has leaked. If you see e-liquid in the threading or pod chamber at the top of your device, use paper towels or cotton swabs to dry the device and the bottom of the tank or pod completely. If your device works now, the leaked e-liquid was preventing your Geekvape from making proper contact with the tank or pod.
To prevent leaks in the future:
- Use a little less air pressure when inhaling if you’re using a puff-activated device. If your Geekvape makes a gurgling sound, you’re puffing too hard.
- When you install a new coil, make sure that it’s pushed or twisted all the way in.
- Don’t overfill your tank or pod.
- Make sure that the tank or pod is closed securely after you refill it.
Clean All Contact Points
Have you been using your Geekvape for more than a few months? If so, it’s possible that the device has gotten fairly dirty. That’s especially likely if you’ve ever experienced a leak – and likelier still if you’re using a pod system, which is likely to develop condensation under the pod because of how the airflow system works. Give your device a thorough cleaning and see if the issue resolves itself.
You can clean the metal contact points on your Geekvape using a cotton swab moistened with a little isopropyl alcohol. Clean the points at the top of the device and on the bottom of your tank or pod. After the cleaning, use a dry cotton swab to remove any remaining liquid before you resume vaping.
Reset the Device and Charge the Battery
Although it’s not common, it’s possible for a Geekvape to display seemingly random error messages in the case of a low battery or transient firmware issue.
- Check the battery indicator. If it’s low, connect the device to your computer to recharge the battery. Wait until the indicator says that the battery is full and try using the device again.
- If the battery isn’t low, try turning your Geekvape off and back on. You can usually do this by pressing the fire button five times.
If your Geekvape has a persistent issue that’s always resolved by turning the device off and back on, you should check the official website for a firmware update. It’s possible that a fix is available.
Make Sure the Tank Is Assembled Properly
If you’re using a Geekvape mod with a glass tank and were unable to resolve the Atomizer Short error by following the previous tips in this article, the next step is to check your tank and make sure that it’s assembled properly – especially if you’ve recently dropped the device.
- Remove the tank from the device and disassemble it completely. Carefully twist the parts back together, making sure that there are no misalignments and confirming that the coil is pushed or twisted in all the way. If the tank’s parts don’t twist back together smoothly, back them up and try again. It’s important to ensure that the components aren’t cross threaded.
- If you dropped your Geekvape on a hard surface, it’s possible that the tank is now misaligned. Examine your device from the side while the tank is installed. Does the mouthpiece point straight up, or is does it seem to veer off at an angle? If it’s not straight, the tank’s top or bottom hardware is coming apart. You may be able to push the components back together with pliers.
Replace the Coil or Pod
If your Geekvape has ever been dropped or damaged, skip to the next section of this guide. Otherwise, if you’ve been unable to fix the Atomizer Short message by following the previous steps, it’s possible that your device’s coil – or the pod, if it has a built-in coil – is faulty. You should try replacing it and see if that resolves the issue.
Evaluate Potential Damage to the Device
Did your Geekvape begin displaying an Atomizer Short message after it was damaged by being dropped on a hard surface or in deep water? If so, you could consider the possibility that the drop may have caused permanent damage.
Many Geekvape devices have IP67- or IP68- level ingress protection, which means that they’re designed to be dustproof and water resistant. Geekvape devices also often have features like rubber pads to help provide shock resistance. Nevertheless, you shouldn’t assume that your device will continue working if you’ve washed it in your washing machine or driven your car over it. If your Geekvape started displaying an error after severe damage, you’ll probably need to replace it.
Can’t Fix the Atomizer Short Error? Here’s What to Do Next
Have you been unable to fix the Atomizer Short error on your Geekvape despite following all of the tips in this article – and are you sure that the device isn’t damaged? Some people have complained online about certain Geekvape mods displaying seemingly random error messages after a few months of use despite being undamaged. The issue seems to relate to a weak solder point under the device’s threading. To fix it, you’ll need to disassemble the device. You’ll also need to be handy with a soldering iron. If your Geekvape is still under warranty, you should consider contacting Geekvape and requesting a new device.
________________________________________________________________________________________________________________
Advertisements placed in our Guest Contribution sections are in no way intended as endorsements of the advertised products, services, or related advertiser claims by NewsroomPanama.com, the website’s owners, affiliated societies, or the editors. Read more here.
